Causes of Kick Well Control Quiz
Quiz-summary
0 of 20 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
Information
Personnel working on the rig are required to understand causes of wellbore influx (kick) so they can prevent well control incidents. This quiz will focus on causes of kick and it will help you learn and remind the well control knowledge. In this test, there are a total of 20 questions and each question has 3 possible answers. You need to take time and think throughout before selecting any answer in order to get the most out of this quest. Additionally, there are few questions related to simple well control calculation. Please feel free to ask any question and enjoy this test.
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 20 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- Answered
- Review
-
Question 1 of 20
1. Question
There are many situations which can cause of well bore influx (kick). Which one is not cause of kick?
Correct
Incorrect
-
Question 2 of 20
2. Question
What is the reason that total reduction in hydrostatic pressure at 20,000 feet is only about 100 psi even though mud density is cut by 50 percent at the surface?
Correct
Incorrect
-
Question 3 of 20
3. Question
What is the condition from the following upon which the well should be shut in immediately?
Correct
Incorrect
-
Question 4 of 20
4. Question
Among the following values, which one is considered to be the normal formation pressure gradient?
Correct
Incorrect
-
Question 5 of 20
5. Question
When is formation pressure considered to be normal from the following statement?
Correct
Incorrect
-
Question 6 of 20
6. Question
In the figure shown below, at 4,000 ft, the formation pressure at a gas water contact is equal to (0.461 psi/ft x 4,000 ft) = 1,844 psi. Gas gradient of this formation is 0.1 psi/ft.
What is the mud weight required at 2,500 ft to balance this pressure formation?
Correct
Reservoir pressure at 2,500 ft = 1844 – (0.1 x 1500) = 1694 psi
Convert 1694 psi to ppg : 1694 ÷ (0.052 x 2500) = 13.03 ppg.
Require mud weight = 13.1 ppg (round up figure from 13.03 ppg)
Incorrect
Reservoir pressure at 2,500 ft = 1844 – (0.1 x 1500) = 1694 psi
Convert 1694 psi to ppg : 1694 ÷ (0.052 x 2500) = 13.03 ppg.
Require mud weight = 13.1 ppg (round up figure from 13.03 ppg)
-
Question 7 of 20
7. Question
What is swabbing?
Correct
Incorrect
-
Question 8 of 20
8. Question
From the following list, which are the correct downhole conditions which tend to increase the likelihood that a well will be swabbed-in when pipe is pulled:
Correct
Incorrect
-
Question 9 of 20
9. Question
What is the general rule to avoid blowouts?
Correct
Incorrect
-
Question 10 of 20
10. Question
What is the primary well control?
Correct
Incorrect
-
Question 11 of 20
11. Question
What is the secondary well control?
Correct
Incorrect
-
Question 12 of 20
12. Question
Which device is used to detect the fluid immediately while drilling?
Correct
Incorrect
-
Question 13 of 20
13. Question
What will happen if the hydrostatic pressure exceeds the fracture gradient of the weakest exposed formation?
Correct
Incorrect
-
Question 14 of 20
14. Question
What precaution shall be taken to avoid excessive pressure created in the annulus?
Correct
Incorrect
-
Question 15 of 20
15. Question
Which one is NOT the POSSIBLEÂ well control indicator?
Correct
Incorrect
-
Question 16 of 20
16. Question
Drilling with a mud cap through hydrocarbon bearing zones is not recommended due to one of the following reason:
Correct
Incorrect
-
Question 17 of 20
17. Question
Which one is NOTÂ the POSSITIVE well control indicator?
Correct
Incorrect
-
Question 18 of 20
18. Question
Displacement of the pipe is 0.5 bbl/stands. How many bbls of displacement you expect once a total of 20 stands are pulled out?
Correct
Volume displacement = 0.5 x 20 = 10 bbl.
Incorrect
Volume displacement = 0.5 x 20 = 10 bbl.
-
Question 19 of 20
19. Question
What should you do if the short fill while tripping out?
Correct
Incorrect
-
Question 20 of 20
20. Question
Why does surge can cause well control situation?
Correct
Incorrect
Leaderboard: Causes of Kick Well Control Quiz
Pos. | Name | Entered on | Points | Result |
---|---|---|---|---|
Table is loading | ||||
No data available | ||||
Good quiz.
Will like to be a part of this medium to better understand Well Control and it’s application at the well site.
I will like to be a part of this medium to have a better understanding of well control and it’s application at the well site.
Dear Sir
Would please send me type of jobe interview questions for night tool pusher
my best regards
I’m beginner in drilling engineering
I’m still beginner
Good
GREAT! & TO YOUR MORE SUCCESS…..
everyone on the drilling rig should take this quiz to refresh information and be aware to use drilling formula
good quiz
thank you iwcf
have any more Q for W&W